Latest posts

Forum Statistics

Threads
25,714
Posts
504,877
Members
27,878
Latest Member
anas
What's New?

Needle size

JackD

JackD

Senior Moderators
Staff Member
Sep 16, 2010
5,806
1,049
I use 23 G 1.5 for almost everything. 23G 1 inch for thighs or delts. I always draw with a 20G.

I use to do an 18g to draw, but noticed there could be little pieces the running stopper that could potentially break off.
 
R

rawdeal

TID Board Of Directors
Nov 29, 2013
3,410
2,305
I use 23 G 1.5 for almost everything. 23G 1 inch for thighs or delts. I always draw with a 20G.

I use to do an 18g to draw, but noticed there could be little pieces the running stopper that could potentially break off.

Always wondered about that rubber stopper "fatigue" possibility, whether or not it resulted from too big a draw pin OR from too many draws from the same vial. I was used to 10ml vials when I first acquired some 20mls ... I stared at those vials and each syringe for a while before I got confident. Never have owned a 50ml vial and not likely to now that my career is headed in the "less is enough" direction.
 
two_slug

two_slug

VIP Member
Mar 7, 2012
553
383
I do 23 gauge x 1" no matter where I inject. 23 makes it go in smoother than the 25 in my opinion
Same here. In my case, I'd rather have a controlled 10 sec injection with a 22g/1 or 23g/1 than trying trying to push something thicker like 250mg cyp or undec through a 25. The only time I'd use a a 25 is with prop, tren a or another short ester where the mg/ml is lower and oil's thin.
 
two_slug

two_slug

VIP Member
Mar 7, 2012
553
383
Always wondered about that rubber stopper "fatigue" possibility, whether or not it resulted from too big a draw pin OR from too many draws from the same vial. I was used to 10ml vials when I first acquired some 20mls ... I stared at those vials and each syringe for a while before I got confident. Never have owned a 50ml vial and not likely to now that my career is headed in the "less is enough" direction.
It is caused by to many draws and/or pulling with to large of a pin. I used to get Mexican vet grade in 50cc vials and would transfer it into 10cc or 20cc vials. No need to have rubber floaties or exposing it to outside air.:)
 
JackD

JackD

Senior Moderators
Staff Member
Sep 16, 2010
5,806
1,049
I used to buy these 19G filter needles to draw when I saw a piece of rubber floating. Miss those suckers. You never know when you need it.
 
kid666

kid666

VIP Member
Jan 28, 2011
1,680
937
I use an 18G blunt to draw and inject with 25GX 1- 1/2
 
ogre

ogre

VIP Member
Dec 18, 2016
204
114
I have used 27x1/2 slin pin for a long time.Its not bad but not fast.
 
ItalianMuscle

ItalianMuscle

Drama Queen senior Vip
Sep 1, 2010
2,509
880
I always withdraw with an 18g
Shoulders 22g/1inch
Glutes 22g/1.5inch
Quad 22g/1inch
 
Littleguy

Littleguy

TID Board Of Directors
Sep 30, 2011
4,066
2,555
Draw with 22 and inj with 25x1.5 I heat it up under hot running water for a few minutes and it plunges quite freely after that.
 
Determined

Determined

VIP Member
Apr 5, 2012
1,425
315
25g 1” for glutes, biceps, medial delt, trap, lats, pecs, thighs
 
Who is viewing this thread?

There are currently 0 members watching this topic

Top